Go Back   Land Rover Forum > Land Rover Specific Models > Discovery II
Register Garage All Albums FAQ Community Calendar Today's Posts Search

Discovery II Discuss here about the second version of Land Rover's Discovery (Disco II) in this section.


View Poll Results: Wont start
Wont start turns over fet a spark just wont start 0 0%
code telling me miss fire 853 0 0%
Code says nuetral position switch circuit high input proble cause 0 0%
Multiple Choice Poll. Voters: 0. You may not vote on this poll

Reply
 
Thread Tools Display Modes
Old 12-16-2011, 10:12 PM   #1
Krissrover
Junior Member
 
Join Date: Dec 2011
Posts: 1
Garage
Question Help

Help 2000 lndr disco 2 149k ran good perfect until was going to work, I came out started it up everything was fine then check engine light came on amd it idled a little rough I decided to run down to the auto store and tell me what was wrong with it I then came back out,to my car and wouldnt start from there not over heated nothing wrong also just changed the oil last week!!! It gets a little bit of a spark to the,plug turns over but wont fire up I dragged it behind a jeep 8( emmbarssed should be other way aroumd autozone told me miss fireing on 853 cyclnders and also nuetural position switch circuit high ik nput proble cause so I got towed behind a jeep 8( bk home were do I start please help call 6025029243 if u can guide me
Krissrover is offline   Reply With Quote
Old 12-17-2011, 04:11 AM   #2
Joey
Senior Member
 
Join Date: Mar 2011
Location: Liberty Twp, OH
Posts: 225
Garage
Default

sounds like the crank position sensor is bad.
__________________
This forum is not used much... please go to:

http://www.landroverworld.org


Joey
Cincinnati OH
http://www.customroveraccessories.com Home of the New D2 horn buttons!

http://www.usarovers.com/ (call for Rover parts ask for Nathan 502-222-5859)

Rover Radio issues or IPOD Adapters http://home.valornet.com/splacket/index.htm

EAS fault http://www.rswsolutions.com

When working with GEMS vehicles. Never try to locate a misfire by pulling plug leads off - pull the injector connector instead. Otherwise you can blow up the ECU.

Secondly never swap ECUs between vehicles to test them, because both vehicles and ECUs may stop working, and you'll have to have them all reset by a franchised LR dealer (ouch!).
Joey is offline   Reply With Quote
Old 02-13-2012, 01:44 PM   #3
unstable
Junior Member
 
Join Date: Feb 2012
Age: 45
Posts: 4
Default

I'm not familiar enough with all of the nuances of the Disco II's electrical / ignition system to say for sure, but I will say that a faulty neutral position switch can usually cause the car to not want to start.

The neutral switch ensures that the car is in neutral or park before it will start to prevent it from trying to start while in gear. Just for laughs you might want to try shifting through all of the gears and see if that yields you any change.
I would guess that the switch would be right there at the shifter and should be easy to fix, you might be able to bypass the switch with a paper-clip or just by joining two wires (all depending on how the switch is configured this may or may not work).

I had problems with my coil pack not long ago and that's also a possibility but it was only causing misfires, I didn't have a no-start condition. Weak spark would also point towards bad wires or bad coil pack(s).

As the other poster mentioned, there's also the possibility that you've got a bad crankshaft sensor. I'm trying to think of how much of a bear that would be to replace...unless I'm mistaken it's sitting on the front of the timing cover. You'd have to tear down the fan / belts, one bolt holds it in, plugs into a weather-proof connector which might be bolted down somewhere as well.

I'd check the neutral safety switch for starters.
unstable is offline   Reply With Quote
Old 02-17-2014, 02:11 PM   #4
AdrnlnRush
Junior Member
 
Join Date: Feb 2014
Posts: 3
Default Crankshaft Position Sensor

Quote:
Originally Posted by Joey View Post
sounds like the crank position sensor is bad.
Joey,

I believe you gave me the advice to change the crankshaft position sensor. The repair seems very straight forward, but my workshop manual tells me that I have to "Reset adaptation codes using TestBook" What does this mean?! and can I do it myself?!
AdrnlnRush is offline   Reply With Quote
Old 02-17-2014, 02:29 PM   #5
AdrnlnRush
Junior Member
 
Join Date: Feb 2014
Posts: 3
Default

Does anyone have any suggestions after changing the crankshaft position sensor, the workshop manual says to "Reset adaptation codes using TestBook" What does this mean and can it be done without taking it to a dealership or shop?!?!
AdrnlnRush is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 09:31 AM.


Sponsor Ads

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.

Garage vBulletin Plugins by Drive Thru Online, Inc.